Audio Authority Series 1500 Installation Guide download pdf (Page 9)

Terminate the ends of each Cat 5e/6 cable with

RJ-45 modular plugs using the EIA 568B

pinout (paired 1-2, 3-6, 4-5, and 7-8). Pre-

made network cables may also be used

for shorter runs. TEST all cables

(including pre-made) with a

network cable tester.

RJ-45 Plug

Pin 1

Clip is pointed

away from you.

Cat 5 Cable Fabrication

RJ-45 plug with pins facing

up and clip facing away.

5 WHITE / BLUE

7 WHITE / BROWN

6 GREEN

3 WHITE / GREEN

2 ORANGE

4 BLUE

8 BROWN

1 WHITE / ORANGE

5 WHITE / BLUE

7 WHITE / BROWN

6 GREEN

3 WHITE / GREEN

2 ORANGE

4 BLUE

8 BROWN

1 WHITE / ORANGE

1 - WHITE/GREEN

2 - WHITE/ORANGE

3 - BLUE

4 - WHITE/BLUE

5 - ORANGE

6 - GREEN

1 - GREEN

2 - ORANGE

3 - WHITE/BLUE

4 - BLUE

5 - WHITE/ORANGE

6 - WHITE/GREEN

Cat 5e/6

CABLES ARE WIRED THE SAME ON

BOTH ENDS (NOT CROSSED OVER).

Using Cable Adjust for Long Cat 5 Cable Runs

For a Cat 5 cable run with total length over 100 feet, use the following

guidelines: Set Cable Adjust Dial on the 1520 in increments of 100 feet (1

= 100 to 199 feet, 2 = 200 to 299, etc.). For 1-way video set only the length

control on the 1501L (Cable Adjust Dial on 1520 = 0). For 2-way video set the

length controls on both the 1520 and 1502L.

Using Trafc Sensors

The 1520 Lane Station provides a connection for Audio Authority’s Model

1547 trafc sensor on the bottom edge of the case (see illustration on page 8).

When a vehicle triggers the 1547, the Counter Station generates a call tone

for the corresponding lane to alert the operator. The call tone for the trafc

sensor can be a different ring tone from the call button at the same lane (see

page 15). To extend a trafc sensor, use an in-line coupler and a length of Cat

5 cable.

Alternatively, a third party trafc sensor may be used by connecting it to the TRAFFIC SENSE terminal and COMMON

terminal as shown on page 8. Third party sensors have different pinouts and color codes. Be sure to verify the specic

pinout with the manufacturer’s documentation.

Playing Audio and Video Content Through Lane Stations

If audio or video messaging content will be playing when customers are on hold or the lane is idle, plug the source

player into the PROGRAM INPUT ports on the 1509SD or 1517SD hub card. Program audio level may be manually

adjusted at the hub. Any lane’s program audio may be turned off during idle periods (still heard while on hold) using the

1550A Program Audio Abate setting (see page 16). If the program video source is a PC, either a composite video card

or external converter is required to scale the PC video output to standard denition composite video signal.

COMPOSITE VIDEO

DVD or MEDIA

VOLUME

CONTROL

AUDIO

COMPOSITE VIDEO

VGA

(VGA OUTPUT)

Wiring

Series 1500 is designed for excellent performance using Cat 5 cable (Cat 5e, Cat 6 or Cat 7 is UTP (Unshielded

Twisted Pair) cable that carries multiple signals for long distances). Follow instructions below, or in retrot installations

where the existing wiring must be used, refer to 1500 alternate wiring instructions (752-502) at www.audioauthority.com.

EXTERNAL

CONVERTER

CABLE

ADJUST

DIAL

1501L OR 1502L

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comments to this Manuals

No comments

Audio Authority Series 1500 Installation Guide Page 9

Comments to this Manuals

Related products and manuals for Door intercom systems Audio Authority Series 1500