6 Audio Authority Model 1170 User Manual
Audio Authority Model 1170 User Manual 7
Installation
This product should be installed by a qualied custom electronics installer.
These instructions address the Model 1170, which is always used with a Model 1166, 1156 or 1171. Refer to
the Model 1166/56 or Model 1171 instruction manual for complete directions for installing this product.
1. Stacking.
a. Lay the Model 1171 or 1156/66 upside down on a protective surface, such as a terrycloth
towel (see expanded view on facing page).
b. Remove the four feet and the bus port cover and save them and their attaching screws for
later use.
c. Plug one end of the bus cable (purchased separately) into the connector visible through the
bus port—apply enough pressure with a plastic or wooden tool to assure that the plug is
completely seated. A center polarizing key is located on the top of each bus plug. Note that
there is a right end and a wrong end to the bus cable.
d. Turn the Model 1170 to be stacked upside down, thread the bus cable through its bus ports,
and engage its four threaded studs with the four threaded holes in the Model 1171 or 1156/66
formerly occupied by the feet.
e. Tighten the hex head screws in the bottom of the stacking product in sequence a few turns
each, until they are all lightly snug.
f. Plug the next plug of the bus cable into the connector as in 1.c.
g. Continue this stacking procedure until all units have been stacked. Always plug the last
connector of the bus into the bottom unit, pushing any excess cable into the empty space
inside the unit. View the bus through the bus port to be sure all plugs are fully seated.
h. Install the bus port cover and feet you removed from Model 1171 or 1156/66 on the bottom
Model 1170 and turn the stack right side up.
2. Rack Mount Adapters. Do these steps if you are installing this product or a stack of products in a
19-inch equipment rack.
a. Remove the cover screws adjacent
to the front panel of each product
and use them to mount Model
1191 rack adapters. Be sure to
place a cylindrical metal spacer
under the adapters at every screw
location.
b. Use a straightedge to line up rack
adapters on a stack of product.
3. Wallplate Hookup. Caution! Do not connect A and B cables incorrectly. Do not apply system
power until cables are tested and A and B connections are veried.
a. Pull two lengths of good quality Category 5e or 6 UTP cable
from the main system to each Wallplate location. Carefully mark
cables of each pair A and B; if they are connected incorrectly,
damage to the Wallplate may result. It is best to use a different
cable jacket color or labels for A and B to insure proper
connection.
b. Install an RJ-45 plug on each end, using EIA-568B pairing
(pins 1-2, 3-6, 4-5, 7-8). Check each cable with a professional
network cable tester before plugging it into the 1100 Series
system. Continuity testing is not adequate! The twisted pairs
CAUTION! This product will
be damaged if spacers are not
used on every screw.
!
1 2 3 4 5 6 7 8
W-O O W-GR BL W-BL GR W-BR BR
Pair 2 Pair 4Pair 1
Pair 3
T568B Pair Assignments
Modular Jack (RJ-45)
1 2 3 4 5 6 7 8
W-O O W-GR BL W-BL GR W-BR BR
Pair 2 Pair 4Pair 1
Pair 3
T568B Pair Assignments
Modular Jack (RJ-45)
!
(17 pages)
(41 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals